Thai University RankingsRESEARCH RADAR
← กลับฐานข้อมูลงานวิจัย
งานใหม่ที่น่าจับตา

Effect of ZrOO\(_{2}\) Content and Oxide Additives on the Wear Resistance of Pressureless-Sintered Si3N4 – ZrOO\(_{2}\) Composites

Effect of ZrOO\(_{2}\) Content and Oxide Additives on the Wear Resistance of Pressureless-Sintered Si3N4 – ZrOO\(_{2}\) Composites

สัญญาณผลกระทบ71/100
01

ข้อมูลจากบทคัดย่อ

ยังไม่มีสรุปภาษาไทยสำหรับระเบียนนี้
ด้านล่างเป็นบทคัดย่อต้นฉบับภาษาอังกฤษจากข้อมูลบรรณานุกรม โปรดตรวจบทความต้นฉบับก่อนอ้างอิง

Silicon nitride (Si3N4) and zirconia (ZrO2) ceramics are well-known for their excellent wear resistance, high hardness, and high mechanical strength. This research focuses on the development and investigation of Si3N4–ZrO2 ceramic composites. Test specimens were fabricated by pressureless sintering at 1550-1650 oC for 2 hours in a nitrogen atmosphere, using SiO2, MgO, and Y2O3 as sintering additives. Density measurements indicated that the weight ratio of SiO2:MgO:Y2O3 at 3:3:5 promoted densification and improved with the addition of ZrO2 (3 mol% yttria-stabilized zirconia). However, the hardness of Si3N4 containing 5 wt% ZrO2 was 14.63 GPa and showed a decreasing trend as the ZrO2 content increased to 50 wt%. For the composite containing 75 wt% ZrO2, the hardness dropped to 10.18 GPa when sintered at 1600 oC. The flexural strength of sintered Si3N4 reached 924.42 MPa, which was comparable to that of pure ZrO2 at 977.93 MPa. High-stress abrasion resistance testing according to ASTM B611 showed that the sample containing 5 wt% ZrO2 exhibited the lowest volume loss of 18.97 mm³. In comparison, pure Si3N4 showed a volume loss of 25.10 mm³ under the same conditions, indicating that a small addition of 5 wt% ZrO2 can enhance wear resistance. In contrast, the sample with 75 wt% ZrO2 had the highest volume loss of 638.73 mm³, while the 100 wt% ZrO2 sample showed a loss of 543.74 mm³. The results demonstrate that optimum wear resistance is achieved through a balance between zirconia content and liquid-phase stability rather than maximizing zirconia concentration.

02

เหตุผลที่อยู่ในฐานติดตาม

ระเบียนนี้ได้รับ Impact Signal 71/100 จากความใหม่ แหล่งเผยแพร่ ความร่วมมือ และสัญญาณในข้อมูลบรรณานุกรม คะแนนนี้ใช้จัดลำดับการติดตาม ไม่ใช่การตัดสินคุณภาพงานวิจัย

ประเด็นที่เกี่ยวข้อง: Advanced ceramic materials synthesis · Advanced materials and composites · Tribology and Wear Analysis

03

บทบาทของนักวิจัยและสถาบันไทย

Kamol Traipanya · Thanakorn Wasanapiarnpong · Charusporn Mongkolkachit · Chulalongkorn University · National Science and Technology Development Agency

04

ข้อจำกัดของข้อมูล

หน้านี้เป็นระเบียนบรรณานุกรมและข้อมูลจากบทคัดย่อ ยังไม่ใช่บทวิเคราะห์ฉบับเต็มหรือการประเมินคุณภาพงานวิจัย ควรตรวจสอบ DOI และเอกสารต้นฉบับก่อนนำไปอ้างอิง